RESOLUTION OF THE STATE COMMITTEE ON STANDARDIZATION OF THE REPUBLIC OF BELARUS

of February 15, 2018 No. 10

About change of the resolution of the State committee on standardization of the Republic of Belarus

Based on subitem 6.1 of Item 6 of the Regulations on the State committee on standardization of the Republic of Belarus approved by the resolution of Council of Ministers of the Republic of Belarus of July 31, 2006 No. 981 "Questions of the State committee on standardization of the Republic of Belarus", the State committee on standardization of the Republic of Belarus DECIDES:

1. Bring in the Rules of confirmation of conformity of National system of confirmation of conformity of the Republic of Belarus approved by the resolution of the State committee on standardization of the Republic of Belarus of July 25, 2017 No. 61 (The national legal Internet portal of the Republic of Belarus, 14.10. 2017, 8/32456), following amendments and changes:

1.1. to add subitem 4.1 of item 4 after words of "certification of products" with the words "directly in the place of implementation of activities for production";

1.2. state Item 12 in the following edition:

"12. The objects of assessment of conformity which are subject to obligatory confirmation of conformity and forms of confirmation of conformity are established by technical regulations of the Republic of Belarus, the Customs union and Eurasian Economic Union (further if other is not determined, – technical regulations) or the President of the Republic of Belarus or according to the procedure, determined by it, due to the need of initiation of efficient measures of state regulation.";

1.3. in part two of Item 27 of figure "12" to replace with figures "10";

1.4. in Item 30:

from word part one "seal of certification body, and also" to exclude;

"its seal (for the individual entrepreneur – in the presence) and" to exclude from word part two;

1.5. in Item 36:

in subitem 36.2:

in part one of figure "5-12" to replace with figures "5-13";

the second to state part in the following edition:

"When carrying out repeated certification by certification body positive results of periodic assessment of the certified products (performance of works, rendering services) which are carried out not earlier than before 12 months before repeated certification, taking into account degree of potential danger of products (performance of works, rendering services), stability of its quality and production process (process of performance of works, rendering services), actions of test reports, the analysis of information on the changes made to technical documentation and engineering procedure of production of the certified products provided by the certificate holder of compliance (performance of works, rendering services), availability during effective period of the certificate of conformity of the facts of carrying out unplanned periodic estimates can be considered.";

in part three of figure "13" to replace with figures "14";

add subitem 36.3 with part two of the following content:

"When carrying out repeated certification by certification body positive results of periodic assessment of the certified competence of personnel which is carried out not earlier than before 6 months before repeated certification can be considered.";

1.6. to exclude from part one of Item 40 of the word "and seal of certification body";

1.7." (person authorized by the manufacturer)" to exclude from part one of Item 54 of the word;

1.8. in Item 59:

to exclude paragraphs of the fifth or eighth of subitem 59.1;

in subitem 59.2:

the third or fifth to exclude paragraphs;

to consider paragraphs of the sixth and seventh respectively paragraphs the third and fourth;

1.9. state Item 60 in the following edition:

"60. The documents performed in foreign language are followed by transfer on Belarusian or Russian, the signed applicant on carrying out certification.";

1.10. in Item 61:

in paragraph one of figure "10" to replace with figure "5";

the fourth to exclude the paragraph;

to consider paragraphs of the fifth and sixth respectively paragraphs the fourth and fifth;

the fifth to exclude the paragraph;

1.11. state Item 73 in the following edition:

"73. In case of availability of the protocol (protocols) of the testing which are carried out in accredited test laboratory (center) on the component parts which are part of products, nodes and blocks, testing on the indicators provided with data application of component parts, nodes and blocks can not be carried out if other is not established by the technical regulation.

In case of availability of the protocol (protocols) of the testing which are carried out in accredited test laboratory (center) for the raw materials and materials used in case of production of products, testing on the indicators which are not changing in production process and provided with use of these raw materials and materials can not be carried out if other is not established by the technical regulation.";

1.12. the fifth to state the paragraph to part two of Item 74 in the following edition:

"for construction materials and products – according to the technical regulation of the Republic of Belarus "Buildings and constructions, construction materials and products. Safety" (TP 2009/013/BY), the approved resolution of Council of Ministers of the Republic of Belarus of December 31, 2009 No. 1748 (The national register of legal acts of the Republic of Belarus, 2010, No. 15, 5/31029).";

1.13. in Item 75 of the word of "batch of these products" shall be replaced with words "provided that products are made by the same manufacturer and is identical to destination and to technical characteristics of the tested products, and also";

1.14. from the paragraph of the fourth Item 78 the second offer to exclude;

1.15. in Item 96 of figure "14" to replace with figures "10";

1.16. state Item 104 in the following edition:

"104. For recognition of the foreign certificate of conformity on batch of certified production the applicant on carrying out certification represents to certification body the original or the copy of the foreign certificate of conformity signed by the holder of the original of the foreign certificate of conformity or the certification body which issued the foreign certificate of conformity.

For recognition of the foreign certificate of conformity on products of serial production the applicant on carrying out certification represents the copy of the foreign certificate of conformity signed by the certification body which issued the foreign certificate of conformity.

For recognition of the foreign test report the applicant on carrying out certification represents the copy of the foreign test report signed by the holder of the original of the foreign test report or the test laboratory (center) which issued the foreign test report.";

1.17. add Item 115 with the offer of the following content: "One copy of the decision (the statement from the decision) goes to the applicant for carrying out certification.";

1.18. state Item 116 in the following edition:

"116. The specialists participating in the considered works on certification of products do not take part in decision making.";

1.19. the Item 120 after the word is "drawn up" to be added with the words "on the form of the certificate of conformity";

1.20. from subitem 121.7 of Item 121 of the word "person authorized by the manufacturer or" and ", or "person authorized by the manufacturer"," to exclude;

1.21. from Item 122 of the word", the signature is certified by seal of certification body" to exclude;

1.22. in Item 123:

the second to state part in the following edition:

"Appendix is drawn up on the form of the copy of the certificate of conformity and is integral part of the certificate of conformity.";

the fourth to state part in the following edition:

"Each sheet of appendix shall be numbered, contain registration certificate number of compliance, the signature of the head or the official authorized by the head and the expert-auditor with indication of the positions held by them, surnames and initials.";

1.23. state Items 126 and 127 in the following edition:

"126. Planned periodic assessment of the certified products if other is not established by the technical regulation, is carried out two times during effective period of the certificate of conformity:

the first – not earlier than in 18 months from registration date of the certificate of conformity by carrying out the analysis of condition of production or the analysis of results of periodic assessment of the certified quality management system (system of management of safety of food products);

Disclaimer! This text was translated by AI translator and is not a valid juridical document. No warranty. No claim. More info