ORDER OF THE MINISTER OF EMERGENCY SITUATIONS OF THE REPUBLIC OF KAZAKHSTAN

of May 6, 2022 No. 148

About modification and amendments in the order of the Minister of investments and development of the Republic of Kazakhstan of December 30, 2014 No. 358 "About approval of Rules of ensuring industrial safety in case of operation of the equipment working under pressure"

I ORDER:

1. Bring in the order of the Minister of investments and development of the Republic of Kazakhstan of December 30, 2014 No. 358 "About approval of Rules of ensuring industrial safety in case of operation of the equipment working under pressure" (it is registered in the Register of state registration of regulatory legal acts for No. 10303) the following changes and amendments:

in the Rules of ensuring industrial safety in case of operation of the equipment working under pressure approved by the specified order:

state Item 1 in the following edition:

"1. These rules of ensuring industrial safety in case of operation of the equipment working under pressure (further - Rules) are developed according to the subitem 14) of article 12-2 of the Law of the Republic of Kazakhstan "About civil protection" (further – the Law) and determine procedure for ensuring industrial safety in case of operation of the equipment working under pressure.";

to state heading of Chapter 1 in the following edition:

"Chapter 1. General provisions";

state Item 2 in the following edition:

"2. In these rules the following terms and determinations are used:

1) the boiler – the device intended for heating of the water which is under pressure above atmospheric and used as the heat carrier out of this device;

2) the boiler – the device intended for development of vapor with pressure is higher atmospheric, used out of this device;

3) power technological copper – steam or the boiler in which fire chamber conversion of technological materials is performed;

4) the boiler superheater – the device intended for temperature increase of vapor is higher than temperature of pressure of saturation corresponding to pressure in copper;

5) the autonomous boiler superheater boiler superheater who is built in copper or the gas flue or separate in which vapor for overheat arrives from external source;

6) the economizer – the device warmed by products of combustion of fuel and intended for heating or partial evaporation of the water arriving in the boiler;

7) the autonomous economizer – the economizer which is built in copper or the gas flue which warmed-up water fully or partially is used out of this copper, or the separate economizer which warmed-up water fully or partially is used in the boiler;

8) settlement resource of copper – duration of operation of copper (element) during which the manufacturer guarantees its work on condition of observance of the mode of operation specified in management of the manufacturer, and settlement number of start-up from cold and hot condition;

9) safety devices – the devices intended for protection of vessels water-heating and boilers, pipelines of vapor and hot water from exceeding of pressure or temperature over admissible sizes of the device;

10) cylinder – the vessel having one or two mouths for installation of gates, flanges or unions, intended for transportation, storage and uses compressed liquefied or dissolved under pressure of gases;

11) barrel – the vessel of cylindrical or other form which is rolled from one place on another and is put on end faces without the additional support intended for transportation and storage of liquid and other substances;

12) capacity – the amount of internal cavity of vessel determined by the nominal sizes set on drawings;

13) pressure internal (outside) – pressure operating on internal (outside) surface of wall of vessel;

14) pressure trial – the excessive pressure with which testing of the equipment for durability and density is made;

15) pressure working – the maximum excessive pressure arising in case of normal course of working process;

16) pressure settlement – pressure on which to be made calculation on durability;

17) pressure conditional – the settlement pressure at temperature of 20 degrees Celsius (further – With °) used when calculating on durability of standard vessels (nodes, details, armature);

18) the admissible temperature of wall maximum (minimum) – the maximum (minimum) temperature of wall at which operation of vessel is allowed;

19) pressure permitted – the most admissible excessive pressure for the equipment (element) established based on assessment of conformity and (or) control calculation on durability;

20) vessel – the hermetically sealed reservoir (which is stationary established or portable), intended for conducting chemical, thermal and other engineering procedures, and also for storage and transportation of gaseous, liquid and other substances;

21) the feedwell – the cylindrical cover of the closed profile opened from end faces;

22) the bottom – the integral part of the case of vessel limiting internal cavity from end face;

23) temperature of working environment – the minimum (maximum) temperature of the circle in case of normal course of engineering procedure;

24) wall temperature settlement – temperature at which physicomechanical characteristics are determined the allowed tension of material also is carried out calculation on durability of elements of the equipment;

25) the tank – the portable vessel which is constantly established on frame of the rail car, on the chassis of the car (trail car) or other vehicles, intended for transportation and storage of gaseous, liquid and other substances;

26) residual resource – total operating time of object from the moment of control of its technical condition before transition to limiting condition;

27) service life settlement – the service life in calendar years established when designing and estimated from the date of commissioning of the equipment;

28) settlement resource of vessel (element) – duration of operation of vessel (element) during which the manufacturer guarantees its work on condition of observance of the mode of operation specified in management of the manufacturer, and settlement number of start-up from cold and hot condition;

29) the service life appointed – the calendar duration of operation of the equipment in case of which achievement operation shall be stopped irrespective of its technical condition;

30) the expert opinion – result of expertize of industrial safety about compliance of dangerous technical devices, to requirements of industrial safety;

31) production schedules – the internal regulating document of the company establishing the sequence and methods of conducting works, requirements and measures for safety of the carried-out work types;

32) the certified organization – the organization certified on the right of conducting examination in the field of industrial safety;

33) engineering certification – the complex of actions providing carrying out external examination, internal survey of surfaces of processing equipment using the methods of nondestructive control, hydraulic or pneumatic testing providing reliability and mechanical integrity of the equipment throughout the service life specified by the manufacturer in the passport for the purpose of determination of technical condition, possibility of safe operation of the equipment, or carrying out monitoring on condition of availability at the owner of the equipment, techniques and tools providing reliability and mechanical integrity of the equipment taking into account assessment of risk factors of RK which are carried out based on ST "The industry oil and gas. Engineering certification taking into account risk factors".";

state item 4 in the following edition:

"4. All pipelines to which Rules extend are divided into four categories according to appendix 1 to these rules.";

to state heading of Chapter 2 in the following edition:

"Chapter 2. Design of vessels";

Disclaimer! This text was translated by AI translator and is not a valid juridical document. No warranty. No claim. More info