of May 23, 2024 No. 361
About change of the resolution of Council of Ministers of the Republic of Belarus of February 14, 2022 No. 80
Council of Ministers of the Republic of Belarus DECIDES:
1. Bring in appendix to the resolution of Council of Ministers of the Republic of Belarus of February 14, 2022 No. 80 "About confirmation of production of industrial output in the territory of the Republic of Belarus" the following changes:
to state subsection 2.2 of Section 2 in the following edition:
|
"2.2. Machines, machines, parts and accessories | ||
|
26.51.6 |
devices and the equipment other for measurement, control and testing |
fixing to the legal entity of state member of EEU of the rights to design and technical documentation in the amount sufficient for production, upgrades and developments of the corresponding products, for the term of at least 5 years availability in the territory of one of state members of EEU of the service center, authorized to perform repair, after-sale and guarantee maintenance of products use of component parts from the third countries in case of production – no more than 30 percent of the following components (in the presence) 2: managing hardware and software system. In case of hardware and software system availability in case of determination of percentage share of component parts from the third countries the counted percentage share of domestic component parts in addition increases on: 10 percent – in the presence of the software (the system software, the technological mathematical software, the software of the man-machine interface, the software of setup, adjustment, parametrization) and the software of the electric drive made in the territory of state members of EEU 5 percent – in the presence of the hardware (the control unit, power converters (electric drives), the operator console, electric motors of coordinate axes when using in system of numerical control of the hardware made in the territory of state members of EEU) 4 percent – when using electric motors of the coordinate axes made in the territory of state members of EEU. For the purpose of exception of the double entry accounting in case of calculation of percentage share of domestic component parts in case of their availability in the main calculation these component parts do not participate in the specified conditions optical system – lenses, lenses, mirrors and another support, including precision rolling bearing, sliding support, support gidro-, aero magnetic and another details case average and small accomplishment in the territory of the Republic of Belarus the following technological transactions: assembly soldering production (control and measuring) testing, setup and verification of metrological characteristics |
|
28.21.13 (except |
furnaces and horns industrial or laboratory electric; induction or dielectric heating equipment |
fixing to the legal entity of state member of EEU of the rights to design and technical documentation in the amount sufficient for production, upgrades and developments of the corresponding products, for the term of at least 5 years availability in the territory of one of state members of EEU of the service center, authorized to perform repair, after-sale and guarantee maintenance of products use of component parts from the third countries in case of production – no more than 30 percent of the following components (in the presence) 2: managing hardware and software system. In case of hardware and software system availability in case of determination of percentage share of component parts from the third countries the counted percentage share of domestic component parts in addition increases on: 10 percent – in the presence of the software (the system software, the technological mathematical software, the software of the man-machine interface, the software of setup, adjustment, parametrization) and the software of the electric drive made in the territory of state members of EEU 5 percent – in the presence of the hardware (the control unit, power converters (electric drives), the operator console, electric motors of coordinate axes when using in system of numerical control of the hardware made in the territory of state members of EEU) 4 percent – when using electric motors of the coordinate axes made in the territory of state members of EEU. For the purpose of exception of the double entry accounting in case of calculation of percentage share of domestic component parts in case of their availability in the main calculation these component parts do not participate in the specified conditions motor spindle electrospindle working head (laser, hydroabrasive and another) two-axial table uniaxial table superimposed table flat (established on support), including for three-coordinate processing two-axial shpindelny head (without spindle) uniaxial shpindelny head (without spindle) static bezosevy shpindelny head (without spindle), including for three-coordinate processing capstan device of change of the tool (stamp, pallets) shop of the tool shop of pallets struzhkotransporter, device of crushing, briquetting electric source of radiation for the laser and other sources of electrical energy optical system – lenses, lenses, mirrors and another laser index, provision sensor contactless and another the sensor is contact, 3D - the probe and another support, including precision rolling bearing, sliding support, support gidro-, aero magnetic and another pump of high and ultrahigh pressure working cylinder (hydraulic, pneumatic) system gidro-and pneumopreparation system of purification of electrolyte, conversion of oils, lubricant cooling liquids system of supply of lubricant cooling liquids, air the cylinder, pump delivered separately directing to swings, slidings and another screw gear roller, ball and another gearing transfer chain, belt coupling reducer variator (animator) transmission the converter electric – the generator and another cross-piece, ram, crank, rod, bed, portal, column and another rack and other less responsible case, dimensional details details case average and small delta mechanism clip of cartridge (tool) – the hydraulic and pneumatic cylinder clip electromechanism, dish-shaped spring and another brake element of spindle (shaft) – the cylinder and another constructive part (electric components) – cable channels, the alarm system, lighting fixtures, cases obstacle device (room protection) accomplishment in the territory of the Republic of Belarus the following technological transactions: assembly production (control and measuring) testing machining of details of the machine heat treatment of details of the machine procurement activities (laser, plasma, hydroabrasive, mechanical cutting of details of the machine) welding or listogibochny works (in the presence) |
|
28.4 (except |
machines for processing of metals, stone, tree and similar solid materials | |
|
28.41.32.600 |
scissors and the press mechanical for processing of metals without numerical control (except the combined penetrative and vysechny machines) |
fixing to the legal entity of state member of EEU of the rights to design and technical documentation in the amount sufficient for production, upgrades and developments of the corresponding products, for the term of at least 5 years availability in the territory of one of state members of EEU of the service center, authorized to perform repair, after-sale and guarantee maintenance of products accomplishment in the territory of the Republic of Belarus the following technological transactions: assembly production (control and measuring) testing machining of details of the machine heat treatment of details of the machine procurement activities (laser, plasma, hydroabrasive, mechanical cutting of details of the machine) welding or listogibochny works |
Disclaimer! This text was translated by AI translator and is not a valid juridical document. No warranty. No claim. More info
Database include more 50000 documents. You can find needed documents using search system. For effective work you can mix any on documents parameters: country, documents type, date range, teams or tags.
More about search system
If you cannot find the required document, or you do not know where to begin, go to Help section.
In this section, we’ve tried to describe in detail the features and capabilities of the system, as well as the most effective techniques for working with the database.
You also may open the section Frequently asked questions. This section provides answers to questions set by users.