11.

Availability of the contract with professional rescue service in the field of industrial safety (further – PASS OPB) on carrying out scheduled and mine-rescue, gas-rescuing, antigushing maintenance on hazardous production facilities and its compliance by the number of rescue equipping, regular rescuers, the special equipment, regimentals and equipment or creation of own professional object rescue services in the field of industrial safety and its compliance by the number of rescue equipping, regular rescuers, the special equipment, regimentals and equipment

rough

775.

Protection availability in places of possible contact of cargo ropes with the main or auxiliary trolley wires of the crane

rough

844.

Availability of limiting efficient limiters of load

rough

844-1.

Availability of operational chains and drafts of the watching cradle navigation system in vertical position

rough

844-2.

Availability of the efficient trailer switches limiting servicing zone

rough

844-3.

Availability of efficient systems of blocking of mechanisms of rise and turn of arrow in case of the elevator which is not exposed on portable support (outrigers)

rough

844-4.

Availability of the efficient device of blocking of system of raising of portable support in case of working provision of arrow

rough

844-5.

Availability of efficient systems of emergency lowering of cradle in case of refusal of hydraulic system, the electric drive or drive of the hydraulic pump

rough

844-6.

Availability of the efficient device protecting from spontaneous promotion of portable support during movement of the elevator

rough

844-7.

Availability of efficient indexes of tilt angle of the elevator

rough

844-8.

Availability of efficient systems of emergency stop of the engine the control panel, as in cradle, and the lower control panel

rough

844-9.

Availability operational the anemometer (for elevators with rise height more than 22 meters)

rough

857.

The devices interfering external and internal examination of vessels (mixers, coils, shirts, plates, partitions and other devices), are provided removable

rough

857-1.

Availability of the internal devices providing removal from air vessel in case of hydraulic testing and waters after hydraulic testing

rough

857-2.

Availability of unions for filling and discharge of water, removal of air in case of hydraulic testing

rough

857-3.

Availability of gates, cranes or other device allowing to exercise control of lack of pressure in vessel before its opening

rough

857-4.

Availability of the devices preventing vessel samooprokidovaniye

rough

857-5.

Availability of grounding of vessels

rough

857-6.

Availability of the hatches and viewing hatches providing survey, cleaning and repair of vessels, installation and dismantle of folding internal devices of vessels

rough

857-7.

Availability of covers of vessels or hatches weighing more than 20 kg. supplied podjemno - rotary or other devices for their opening and closing

rough

865.

Availability of safety valves on the branch pipes or pipelines which are directly attached to vessel.

rough

865-1.

Availability of protection devices from freezing in them working environment

rough

865-2.

Availability of safety valves on discharge pipelines and on pulse lines in places of possible accumulation of condensate of drainage devices, for removal of condensate

rough

865-3.

Availability of the locking and regulating armature between vessel and the safety valve

rough

865-4.

Availability of indexes of control of level of liquid on vessels

rough

865-5.

Availability of sound and other signaling devices and blocking on the level of working environment

rough

865-6.

Availability of protection devices on indexes of level of working environment for protection of personnel from injuring

rough

865-7.

Availability of indexes of level of admissible upper and lower limits

rough

875.

Non-admission of filling with gas of tanks or barrels with expired for surveys

rough

875-1.

Non-admission of filling with gas of tanks or barrels in case of absence or defective fittings and instrumentations

rough

875-2.

Non-admission of filling with gas of tanks or barrels in which there is other gas for which they are intended.

rough

878.

Non-admission of filling of cylinders with expired for surveys, with review period of porous weight

rough

878-1.

Non-admission of filling with the damaged cylinder case, the defective gate

rough

878-2.

Non-admission of filling of cylinders if is absent proper coloring and texts

rough

878-3.

Non-admission of filling of cylinders if is absent the excessive pressure of gas

rough

878-4.

Non-admission of filling of cylinders if there are no established brands

rough

879.

Providing design of coppers on calculated parameters during work, engineering certification, cleaning, washing, repair and operational control of metal

rough

881.

Availability of destructive safety devices on coppers with chamber combustion of fuel (powdered, gaseous, liquid) or with mine fire chamber for combustion of peat, sawdust, shavings or other small production waste

rough

881-1.

Installation and placement of destructive safety devices on copper is determined by the project, for the purpose of non-admission injuring of people

rough

884.

Availability on copper of pipelines of supply of nutritious or network water

rough

884-1.

Availability of systems of purge of copper and descent of water in case of copper stop

rough

884-2.

Availability of the pipeline of removal of air from copper when filling with its water and kindling

rough

884-3.

Availability of systems of purge of the boiler superheater and steam line

rough

884-4.

Availability of the pipeline of sampling of water and couple

rough

884-5.

Availability of pipelines of water drainage or couple in case of kindling and stop

rough

884-6.

Availability of the pipeline of warming up of drums in case of kindling

rough

887.

Availability on coppers of the devices protecting from increase in pressure (safety devices)

rough

887-1.

Availability on coppers of devices of safety, nutritious devices

rough

887-2.

Availability on coppers, except for direct-flow, at least two indexes of water level of direct action

rough

887-3.

Availability and installation of the device for measurement of temperature of superheated vapor on each steam line to the main latch at the coppers having the boiler superheater

rough

892.

Availability on the cargo or spring valve the device for check of operability of operation of the valve in operating time of copper by its forced opening

rough

892-1.

Availability of the taking-away devices from the safety valves protecting personnel from burns in case of their operation

rough

892-2.

Availability of two reduced remote indexes of level in case of poor visibility

rough

892-3.

Availability of locking bodies on the water taking away pipes from safety valves of the boiler, the economizer

rough

892-4.

Availability on the boiler, indexes of water level of direct action

rough

892-5.

Availability on indexes of level of direct operation of boilers of transparent plates

rough

892-6.

Availability on indexes of water level shutoff valves (cranes or gates) for their disconnection from copper and purge

rough

892-7.

Availability on boilers of the trial crane established in the upper part of drum of copper, and in the absence of drum at the water exit from copper in the bulk distribution line to the locking device

rough

892-8.

Availability of the indexes of water level consisting of several separate water-indicating plates

rough

897.

Availability on the coppers having the boiler superheater on each steam line to the main latch of the device for measurement of temperature of superheated vapor

rough

897-1.

Availability on coppers with natural circulation with overheat of vapor with a steam generating capacity more than 20 tons per hour, direct-flow coppers with a steam generating capacity more than 1 tons per hour, the showing devices and devices with continuous registration of temperature of superheated vapor

rough

897-2.

Availability on boiler superheaters with several parallel sections of the devices for measurement of temperature of vapor established on general steam lines of superheated vapor, devices for periodic measurement of temperature of vapor at the exit from each section, and for coppers with temperature of couple above 500 degrees Celsius on output part of coils of the boiler superheater, on one thermocouple (sensor) on each meter of width of the gas flue

rough

897-3.

Availability of devices of continuous action with the registering devices on coppers with a steam generating capacity more than 400 tons per hour for measurement of temperature of vapor on output part of coils of boiler superheaters

rough

897-4.

Availability on copper of parookhladitel for regulation of temperature of overheat of vapor to parookhladitel and after it the device for measurement of temperature of vapor

rough

897-5.

Device availability for measurement of temperature of feedwater on water input in the economizer, at the exit from it and on nutritious pipelines of boilers without economizers

rough

897-6.

Availability of devices for measurement of water temperature for boilers on entrance and exit of water

rough

897-7.

Availability on coppers heating capacity of more 4,19 Gigajoule/hour (1 Gigacalories per hour) registering the device for measurement of temperature at the exit from copper

rough

897-8.

Availability on fuel pipeline of copper of the thermometer for measurement of temperature of fuel before nozzles

rough

900.

Availability of locking body at the exit from copper before its connection with combined steam line of boiler room.

rough

900-1.

Availability at boilers of locking body on water input in copper and at the water exit from copper

rough

900-2.

Protection availability on combined tank from exceeding of pressure is higher settlement in case of withdrawal of the circle from copper (separator, dilator) with smaller pressure, than in copper

rough

900-3.

Availability of remote drives with conclusion of management to workplace of the driver of copper of the principal parozaporny organs of boilers with a productivity more than 4 tons per hour

rough

900-4.

Availability of the regulating armature on nutritious lines of copper

rough

900-5.

Availability on each copper of the devices of safety providing automatic shutdown of copper or its elements in case of variations from the set operation modes

rough

904.

Availability of automatic devices on the boilers with chamber combustion of fuel stopping fuel delivery to torches in case of decrease in level, and for direct-flow coppers - water consumption in copper is lower than admissible

rough

904-1.

Availability of devices on the boilers with repeated circulation and chamber combustion of fuel automatically stopping fuel delivery to torches

rough

904-2.

Availability of devices on the boilers with layered combustion of fuel which are switching-off tyagodutyevy devices in case of pressure decrease of water in system to value in case of which danger of water hammers is created and in case of temperature increase of water is higher than the set limit

rough

904-3.

Availability of automatic devices on the boilers with chamber combustion of fuel preventing fuel delivery in copper fire chamber, and in case of layered combustion of fuel - the disconnecting tyagodutyevy devices and toplivopodayushchy mechanisms of fire chamber

rough

905.

Availability on coppers automatically the operating sound and light signaling devices of the upper and lower limiting provisions of water levels.

rough

905-1.

Availability on steam and boilers in case of chamber combustion of fuel of automatic devices for interruption in supply of fuel in fire chamber in case of blackout of torch in fire chamber, shutdowns of all smoke exhausters or the termination of draft, shutdown of all dutyevy fans.

rough

905-2.

Protection availability on coppers with the torches equipped with individual fans, the stopping fuel delivery to torch in case of fan stop

rough

906.

Availability on copper boiler, using liquid or gaseous fuel, devices, automatically stopping fuel delivery in fire chamber in case of the termination of circulation of water in the boiler

rough

906-1.

Availability of protection of devices of safety against impact of dangerous factors on persons connected with their servicing and repair

rough

906-2.

Availability on boilers of the automatic regulator of food, except for coppers boilers which have selection of vapor on the party in addition to the boiler, does not exceed 2 t/h

rough

906-3.

Availability of explosive safety valves on general gas flues of coppers with chamber burning

rough

918.

Availability of installations before boiler processing of water in all boilers with natural and repeated forced circulation by the steam generating capacity of 0,7 of t/h and more, in all steam direct-flow coppers irrespective of steam generating capacity and in all boilers

rough

924.

Availability on copper of vozdushnik

rough

924-1.

Non-admission of installation of shutoff valves on the pipelines combining vozdushnik of several coppers

rough

924-2.

Availability of manholes, covers, flange connections

rough

924-3.

Availability of devices of suppression of the lit-up heat carrier in fire chamber of coppers

rough

924-4.

Availability of equalization lines during the parallel work of two and more coppers in system with self-flowing return of condensate the lower drums (collectors) of coppers

rough

924-5.

Availability of shutoff valves on coppers from entrance and exit of the heat carrier

rough

924-6.

Availability on the disconnecting and bringing pipelines of the warming devices, for prevention of hardening of the heat carrier.

rough

924-7.

Availability on the pipeline of vapor or heated liquid which is taking away from copper of the devices showing and registering temperature, and on the bringing pipeline, the device, showing temperature.

rough

930.

Availability of indexes of movement on steam lines with internal diameter of 150 mm and more and with the temperature of couple 300 ° C and above, for control of expansion of steam lines and observation of correctness of work of basic and suspended system

rough

930-1.

Availability in the lower points of each section of the pipeline which is disconnected by latches lowered the union

rough

930-2.

Availability of devices for purge of the lower trailer points of steam lines and the lower points

rough

930-3.

Availability of vozdushnik for removal of air in the upper points of pipelines

rough

930-4.

Availability on pipelines of devices for measurement of pressure and temperature of working environment

rough

930-5.

Availability in necessary cases the locking and regulating fittings, reducing and safety devices and remedies and automation for providing safe service conditions in pipelines

rough

930-6.

Availability on the safety valves which are taking away the pipeline, protecting personnel from burns in case of operation of valves

rough

930-7.

Protection availability pipelines from freezing and the equipment drainages for the discharge accumulating in them condensate

rough

930-8.

Availability of devices on cargo or spring valves for check of operability of operation of the valve in operating time of the pipeline by forced opening

rough

930-9.

Availability on reducing and reduktsionno-cooling devices of automatic control of pressure and temperature of vapor

rough

940.

Availability of the drainages providing possibility of conducting control of work during pipeline purge

rough

940-1.

Availability on pipelines for providing safe service conditions of devices for measurement of size of pressure and temperature of working environment, the locking and regulating armature, safety valves, means of the alarm system, protection and automation

rough

940-2.

Availability of grounding of the equipment

rough

940-3.

Availability of the passport of the delivery pipeline

rough

942.

Availability:

- on compressors, the having highly located parts, are equipped with platforms and ladders for their inspection;

- platforms through passage, equipped with handrail;

- on air compressors with a productivity more than 10 cubic meters a minute (further – m3/min.) trailer refrigerators and maslovlagootdelitel;

- barriers on the moving and rotating parts of compressors, electric motors and other mechanisms.

considerable

942-1.

Availability of grounding of cases of electric motors, compressors, intermediate and trailer refrigerators, maslovlagootdelitel

considerable

943.

Installation of compressors with a productivity over 20 m3/min. and their engines in the one-storey fireproof buildings which are separately located from production without garret overlappings with fire-resistant or fire-resistant partitions

considerable

943-1.

Non-admission placement of compressor installations under household, public, office and similar it rooms in which people reside

considerable

944.

Compliance:

- fence (absorption) of air the compressor in the zone protected from action of solar radiation from not gas-polluted and not dusty party at the height at least 3 meters from earth level;

- for the air compressors with a productivity up to 10 m3/min. (inclusive) equipped with air filters, air intake from the room provided that the sucked-in air does not contain dust and harmful gases;

Availability for purification of the sucked-in air of dust with the filter protected from hit in it atmospheric precipitation which is soaking up the compressor air duct.

rough

944-1.

Compressor availability, supplied with trailer refrigerators, equipped with maslovlagootdelitel on pipelines between the refrigerator and air collector

rough

946.

Availability and installation of manometers and safety valves, established after each step of compression and on pressure line after the compressor.

rough

946-1.

Availability and installation of devices for measurement of pressure of working environment after each step of compression of the compressor, on the delivery pipeline, on airgas collectors, on the oil pipeline giving compressor oil for lubricant

rough

946-2.

Availability and installation in front of each manometer of the three-tradable crane for installation of the control manometer, check of operability of operation of the working manometer, its disconnection from source of pressure and connection with the atmosphere

rough

946-3.

Availability and installation of three-tradable cranes with siphon tube with a diameter at least 10 mm, the oil buffer or other device protecting the manometer from spoil under the influence of working environment

rough

946-4.

Availability and installation of the manometers established at the height up to 2 meters from the level of the platform of observation of them shall be at least 100 mm, at the height from 2 to 3 meters – at least 160 mm. - on manometers of brands. Indications of manometers clearly were visible to service personnel, at the same time its scale shall be located vertically or with inclination to 30o for visibility improvement forward

rough

946-5.

Availability and installation of terms of checking if the arrow of the manometer in case of its switching off does not return to the zero indication of scale to the size exceeding half of admissible error for this manometer if glass is broken or are available other damages of the manometer which affect correctness of its indications

rough

953.

Implementation of check of installation sites of valves, selection of working environment from branch pipes on which are established the safety valve

rough

953-1.

Availability of protection against freezing

rough

953-2.

Availability of record about results of setup and adjustment of safety valves in operational documentation

rough

953-3.

Availability of device for forced opening in operating time of compressor installation

rough

953-4.

Non-admission of installation of shutoff valves in front of the safety valve and after it

rough

957.

Availability of stationary mercury thermometers or other sensors.

considerable

974.

Grounding availability in order to avoid ignition of oil and oil deposits in air collectors, gas collectors and pipelines, in case of suction of air or inert gas with the crushed dust and rust.

considerable

990.

Non-admission of warehousing of materials and the equipment on the allocated strips 2 meters wide along the pipeline route and providing quick access of personnel of the gas-distributing organization for carrying out bypass, maintenance and repair of the gas pipeline, localization and liquidation of emergencies by the head of the organizations on which territory the gas pipeline is laid by transit.

rough

990-1.

Carrying out technical inspection of steel underground gas pipelines depending on duration of operation or other conditions by instrument method and nondestructive control methods

rough

994.

1. Technical condition of processing and electric equipment, gas pipelines, sanitary constructions at gas-filling stations, gas-filling Items and stationary automobile gas-filling stations ensure trouble-free operation and safety of personnel.

2. Conducting works on the approved production schedules on production processes in which admissible values of pressure and temperatures of the liquefied oil gas taking into account their physical and chemical properties and explosive characteristics, servicing and repair of armature are determined.

3. Carrying out according to agreed projects, additional installation of processing equipment, expansion or reconstruction of stations and Items. Non-admission of performance improvement of workshops due to deterioration in the safe working conditions working.

4. Emergency stop of compressors and pumps in case of: - to leakage of gas and defective shutoff valves; - emergence of vibration, extraneous noises and knocks; - failure of bearings and epiploons of consolidation; - change of admissible parameters of oil and water; - defects of muftovy connections, wedge-shaped belts and their barriers; - increase or lowering of the established gas pressure in the soaking-up and pressure head gas pipelines; - in case of increase in level of liquid in kondensatosbornik on absorption of the compressor above admissible and in case of temperature increase of gas at the exit from the compressor above admissible.

5. Taking measures to non-admission of operation of pumps and compressors with disconnected or defective automatic equipment and emergency ventilation, and also blocking with fans of exhaust systems.

6. Accomplishment of transactions on discharge, filling on cistern and automobile cars with the written permission of the chief of the gas-filling station, and in festive and the days off – the responsible person on duty on the station. Implementation of constant surveillance over filling, drain and fuel filling columns, cistern and automobile cars, gas-balloon cars during discharge and filling the liquefied oil gas.

7. Ensuring continuous observation of pressure and level of the liquefied oil gas in the tank and acceptance of the reservoir, pressure decrease in reservoirs, truck tanks and cylinders due to dumping of steam phase into the atmosphere in case of their filling, sufficient illumination of railway platform, the reservoir park and purpose of crew as a part of at least 3 people at night in case of plum of the liquefied oil gas from cistern cars. Equipment of the personnel which are carrying out transactions of discharge or filling, and drivers of nasosno-compressor department technical communication.

8. Determination of control and frequency of sampling, and also intensity of smell of gas (odorization) by the organizations, operating gas-filling stations, gas-filling Items, stationary automobile gas-filling stations according to technical acts, production schedules.

rough

994-1.

Providing safe filling or discharge of gas at gas-filling stations and gas-filling Items installation of caps on unions of gates of tanks after completion of filling discharge, spark arrester on exhaust pipe of the vehicle before its entrance on the territory of the gas-filling station, gas-filling Item, and also for implementation of transactions on discharge filling of the liquefied oil gas in the vessels working under pressure, the reservoir park of the stationary automobile gas-filling station, fixing of tanks at railway line after the end of shunting works, compliance of number of the cistern cars which are at the same time in the territory of the gas-filling station does not exceed number of the posts of discharge provided by the project.

rough

998.

Non-admission at the automobile gas-filling station of filling of cylinders, not held for use on motor transport.

rough

998-1.

Non-admission of parking lots of the machines loaded with cylinders, and truck tanks of the liquefied oil gas near places with naked flame and places, where perhaps mass accumulation of large number of people. Observance of distance of 5 meters and more from the parking lot of the machine for the liquefied oil gas to cesspools, cellars and covers of wells of underground communications.

rough

1001.

Equipment of reservoir installation, factory fabricated the gas pressure regulator, safety and locking and safety and waste valves, instrumentations for control of pressure and level of the liquefied oil gas in the reservoir, shutoff valves, pipelines of liquid and steam phases, and also in case of technical need evaporating installations of the liquefied oil gas

rough

1001-1.

Maintenance of the maximum working pressure of the liquefied oil gas after the regulator of reservoir and group balloon installations is not higher 0, мегаПас¬á½ý..... Setup of waste and locking safety valves on pressure equal to 1,15 and 1,25 of the maximum worker. Installation of the disconnecting devices on connecting pipelines on liquid and steam phases of reservoirs of each group among themselves at the number of reservoirs more than two

rough

1001-2.

Observance of required distances from reservoir installations to buildings, constructions of different function and communications

rough

1001-3.

Equipment of reservoir installations by the aired barrier from nonflammable materials height is at least meter 1,6 at distance at least 1 meter, at the same time distance from barrier to outside brow of the closed embankment or the protecting wall from nonflammable materials (in case of elevated installation of reservoirs) meter 0,7 suffices

rough

1001-4.

Observance of requirements for placement of evaporating installations on the open areas or in the separate buildings, rooms (attached or which are built in factory buildings) which level of floor is located above planning mark of the earth, at distance at least 10 meters from barrier of reservoir installation. An hour (200 kilograms an hour) at least 1 meter from underground or elevated storage tanks is allowed to establish cubic evaporating installations with a productivity up to 100 meters directly on roofs of mouths of reservoirs or at distance, and also it is direct at the aggregates consuming gas if they are placed in certain rooms or on the open areas. In case of group placement of evaporators the distance between them is accepted at least 1 meter

rough

1001-5.

Observance of requirements of placement (taking into account the maximum total capacity at distances from buildings and constructions or at walls of gasifiable buildings it is not lower than III degrees of fire resistance of the class C0 at distance from window and doorways) group balloon installation for the liquefied oil gas and its structure (shutoff valves, the gas pressure regulator, the valve balloon with the waste valve working in case of exceeding of admissible pressure more than for 15%, preventing the explosion of cylinder showing the manometer and pipelines of high and low pressure)

rough

1001-6.

Observance of requirements of placement (distance, quantity admissible cylinder in buildings and its number of storeys) and arrangement (at distance in light meter 0,5 from window openings and 1,0 meter from doorways of the first floor suffices, 3,0 of meters from door and window openings of ground and basement stores, and also sewer wells suffices. Placement compliance near the public or factory building no more than one group installation) individual balloon installations in buildings and constructions

rough

1001-7.

Non-admission of establishment in rooms of cylinders with gas at distance less than 1 meter from radiators of heating and other heating devices and furnaces and less than 5 meters from heat sources with naked flame and protection against damages by transport and heating is higher than 45 degrees on Celsius scale in case of installation of cylinder of the liquefied oil gas out of the room

rough

1001-8.

Non-admission installation of cylinders of the liquefied oil gas:

1) in living rooms and corridors;

2) in socle both basements and attics;

3) in the rooms located under and over: lunch and trade floors of catering establishments, audiences and educational classes, visual (assembly) halls of buildings, hospital chambers, other similar rooms;

4) in rooms without natural lighting;

5) at emergency exits;

6) from the main facades of buildings.

rough

1002.

Observance of application of cylinders service life no more than 30 years and compliance of the put coloring, texts and strips on cylinders.

rough

1002-1.

Operation of cylinder of easily readable data which are not put on the upper spherical part of each cylinder about the trademark of the manufacturer; numbers of cylinder; actual mass of empty cylinder (kilograms): for cylinders with a capacity up to 12 liters inclusive – to within 0,1 of kilograms; over 12 to 55 liters inclusive – to within 0,2 of kilograms, the mass of cylinders with a capacity over 55 liters is specified according to documentation of the plant; manufacturer; date (month, year) of production and year of the following survey; working pressure P, megapascals (kilograms of force on centimeter square); trial hydraulic pressure of the RPR, megapascals (kilograms of force on centimeter square); capacity of cylinders, liter: for cylinders with a capacity up to 12 liters inclusive – nominal, for cylinders with a capacity over 12 to 55 liters inclusive – actual to within 0, liter, for cylinders with a capacity over 55 liters – according to regulating documents on their production; brand of Quality Department of the manufacturer (except for standard cylinders with a capacity over 55 liters); number of the standard for cylinders with a capacity over 55 liters.

rough

1002-2.

Maintaining register of filling of cylinders by filling stations and control of the filled cylinders when filling cylinders the compressed, liquefied and soluble gases. Maintaining the separate magazine of filling on each gas if at one station filling of cylinders is made by different gases.

rough

1002-3.

Rejection of cylinders in cases of identification of cracks, dents, отдулин, sinks more than 10% in depth from the nominal thickness of wall, anguishes and vyshcherbleniye, depreciation of carving of mouth, and also lack of some passport data on cylinder, reduction in worthlessness of defective cylinders by drawing notches on carving of mouth or drilling of openings in the case.

rough

1002-4.

Filling non-admission by gas of cylinders at which the term of the appointed survey expired; the review period of porous weight expired; the cylinder case is damaged; gates are defective; there are no proper coloring or texts; there is no residual pressure of gas of at least 0,5 of the atmospheres; there are no established brands.

rough

1002-5.

Availability separately specially equipped rooms for carrying out survey of cylinders.

rough

1002-6.

Adherence to deadlines (at least in 5 years) survey of cylinders for acetylene and check of condition of porous weight (at least in 12 months) with drawing brand on each cylinder.

rough

1002-7.

Ensuring carrying out terms and procedure for survey of the cylinders which are on long warehousing. Prevention of fall, collision and formation of spark in case of storage of cylinders.

rough

1002-8.

Non-admission of storage in one room of cylinders with oxygen and combustible gases.

rough

1002-9.

Availability of protection of cylinders against atmospheric precipitation and sunshine.

rough

1002-10.

Availability in warehouse of the hung-out instructions, rules and posters on the address with cylinders.

rough

1002-11.

Providing warehouses for storage of the cylinders filled with gases one-storey with coverings of easy type without garrets, the performed walls, partitions, coverings from fireproof materials is not lower than II degrees of fire resistance, windows and doors opened outside, coloring of glasses in window and doorways white paint or use of opaque glasses, height 3,25 of meters from floor to the lower speakers of parts of roofing covering, floors equal with nonslipping surface, and warehouses for cylinders with combustible gases – with surface from the nonflammable materials excluding sparking in case of blow about them any objects suffices.

rough

1002-12.

Equipment of warehouses for cylinders according to regulations for the rooms dangerous concerning explosions, and warehouses from explosion and flammable gases lightning protection devices.

rough

1002-13.

Equipment of warehouses for the cylinders filled with gas natural or artificial ventilation.

rough

1002-14.

Separation of storage facilities for storage of cylinders fireproof walls on compartments, is stored no more than 500 cylinders (40 liters) with combustible or poisonous gases in each of which and no more than 1000 cylinders (40 liters) with nonflammable and nontoxic gases. Separation by fireproof partitions height is at least meter 2,5 with open apertures for pass of people and apertures for means of mechanization of compartments for storage of cylinders with nonflammable and nontoxic gases. Each compartment has independent exit outside.

rough

1002-15.

Availability at the organization carried out filling and engineering certification of cylinders, including cylinders for acetylene registered brand with the corresponding code in territorial subdivision of authorized body.

rough

1004.

1. Non-admission of zanimaniye and ensuring access for service personnel to rooms in which gas pipelines are laid and are established gas-using aggregates and fittings. Non-admission of loading of gas pipelines foreign designs and objects, and their use as supporting frameworks and grounding.

2. Ensuring work of gas-consuming installations with the switched-on devices of control and protection with permanent observation from service personnel. Removal of signal of gas contamination of the room and defect of the equipment on control office or to the room with permanent presence of the working personnel in case of operation of installations without permanent observation of their work on condition of the equipment of installations by system of the automation ensuring trouble-free operation of the gas equipment and antiemergency protection in case of malfunctions and defects.

3. Ensuring required maintenance of internal gas pipelines and gas equipment. Conducting check and clearing of gas flues in case of accomplishment of repair of furnaces, coppers and other gas-using equipment, and also in case of draft violation.

4. Disconnection from gas pipelines of the gas equipment before repair, survey and repair of fire chambers or gas flues and in case of conclusion from work of installations of seasonal action with installation of cap after shutoff valves.

5. Providing with the owner or the operating organization before inclusion in work of installations of seasonal action, including heating coppers carrying out: examination and instructing of service personnel concerning labor protection and industrial safety; running repair of the gas equipment and system of automation; clearings of gas pipelines, checks of their operability, and also systems of ventilation; checks of flues and ventilating channels with execution of acts.

6. Creation and approval by the owner or head of the operating organization on each gas-using installation based on the technical report of the specialized organization of the regime card of work of installation. Posting of the approved cards at each gas-using installation.

rough

1004-1.

Application on gas-using installations of the systems of automation ensuring trouble-free operation of the gas equipment and antiemergency protection in case of malfunctions, defects and the fire

rough

1010.

1. Ensuring conducting check of operation of devices of protection, blocking and the alarm system at least 1 time a month, and also after the end of repair of the equipment.

2. Conducting check of signaling device of gas contamination on compliance to parameters with use of control gas-air mixture without deliberate zagazovyvaniye of the room.

3. Replacement removed for repair or check of devices on identical, including under the terms of operation. Equipment by figurative devices for control of concentration of gas in air of production rooms.

rough

1010-1.

Ensuring operation of the gas equipment with the switched-on instrumentations, blocking and the alarm system provided by the project

rough

1013.

Equipment of gas pipelines of coppers blow-off gas pipelines with locking devices (at the end of each deadlock section of the pipeline or in front of the locking device of the last on the torch gas course (in case of absence deadlock sites on gas pipelines); on the gas pipeline to the first locking device before each torch with its length to the first locking device more than 2 meters) and unions for sampling, including if necessary the rastopochny blow-off gas pipeline.

rough

1013-1.

Non-admission of combination of blow-off gas pipelines with safety pipelines, and also gas pipelines of one appointment with the different pressure of gas.

rough

1013-2.

Equipment of the installed gas boiler installations by technological protection, blocking and the alarm system.

rough

1015.

1. Availability of the specialized divisions (services of emergency recovery operations, emergency and dispatching services, emergency posts) created by the gas supplying organizations with the round-the-clock operating mode, including days off and holidays, for localization and liquidation of incidents and accidents on objects of gas-distributing and gas-consuming systems.

2. Holding training occupations with emergency crews in each organization with subsequent assessment of actions of personnel and logging in terms:

1) according to plans of localization and accident elimination for each subject, for each crew – at least 1 time in 6 months;

2) according to plans of interaction of services of different function – at least 1 time a year.

3. Registration of requests in emergency and dispatching service in the special magazine of registration of emergency requests. Carrying out the analysis of all requests with the subsequent development of actions for improvement of the organization of maintenance of objects of gas supply system and execution of the analysis references in recommended forms.

4. Execution of the technical act on each accident, incident (accident).

considerable

1015-1.

Equipment of emergency crews by the special machine equipped with radio station, siren, the flashing indicator of blue color and completed with the tool, materials, control devices, the equipment and devices for timely localization of incidents and accidents and their effects, tablets (route cards) and necessary executive technical documentation (plans of the gas pipeline with bindings, schemes of welded joints).

considerable

1020.

Availability and the actual accomplishment developed and approved as the head of the organization of regulations on production supervision; production schedules; plan of liquidations of accidents

rough

1022.

Ensuring issue written the job specification admissions on performance of works of the increased danger in form. Ensuring specifying in the job specification admission of dangerous factors, delimitations of the site or object in case of the admission of third party for performance of works on the object territory.

rough

1027.

All servicing platforms, transitional bridges and ladders, it is necessary to carry out strong, steady, and also to supply with handrail (except vertical ladders) at least 1 m high with crossbeam and continuous covering on bottom of handrail on m 0,14 height).

considerable

1035.

Availability of reliably fixed barriers excluding access to all moving and rotating parts of machines and mechanisms, elements of the drive and transfer. All open moving parts of the equipment located at height to 2,5 of meters (inclusive) from the level of floor or available to accidental touch from working platforms are protected. The barrier is carried out continuous or mesh with size of cells of 20х20 millimeters.

rough

1036.

Availability of continuous barriers on tooth, belt and chain gearings irrespective of height of their arrangement and speed of rotation.

rough

1066.

Availability of blocking on the cam, horizontal and vertical molotkovy crushers excluding possibility of start of crusher in case of open cover of the case

rough

1117.

Availability of continuously working ventilation during the operation of the filtering devices with harmful allocations

rough

1120.

Non-admission of work on the evaporating device with defective shutoff valves, safety valves and manometers, in case of the switched-off exhaust ventilation, the open device, without safety points and in case of defective viewing glasses.

rough

1131.

Availability of the exhaust ventilation in all rooms in which atmosphere appearance of unhealthy people of gases, aerosols, impurity is possible to equip with the corresponding instrumentations with systems of the alarm system about exceeding of threshold limit values of hazardous substances

considerable

1156.

Availability of the automated control and process management of desorption and regeneration.

rough

1156-1.

Availability of continuously operating automatic devices of control of the air circle, blocked with system of the alarm system (sound, light) notifying on exceeding on workplaces of content of threshold limit value of vapors of cyanhydric acid in rooms of sorption, desorption, regeneration, storage and preparation of reagents.

rough

1176.

Temperature not above 25 degrees Celsius is maintained in rooms for warehouses of xanthogenates, sulphurous sodium and cyanides.

rough

1176-1.

Non-admission storage of poisonous reagents and not extinguished lime together with other reagents

rough

1177.

Extract availability from the lower and upper zones of the room for the purpose of exception of formation of congestive zones in rooms for storage of the reagents allocating the explosive vapors and gases having toxic action or unpleasant smell.

rough

1191.

Availability of local suctions of the exhaust ventilation blocked with reserve ventilating installation on all equipment and installations intended for opening of barrels with cyanide, unloadings in the bunker and tubs solvents for dissolution and storage of ready solutions

rough

1198.

Availability of blocking on doors of the hatches intended for access for people to mixing drums and drums cooling agents in case of their cleaning and repair and also the blocking excluding possibility of launch of the reel in work with open door (in case of local and in case of remote control).

rough

1200.

Availability of the automatic blocking cutting intake of gas in gas torches of machines of okuskovaniye (agglomerative machines and machines of roasting of pellets)

rough

1204.

Availability of barriers of zone of the working platform of agglomerative and indurating machines in places of loading of bed and furnace charge on carts; on drives of rollers of rolikoukladchik and face part of machines.

rough

1272.

In case of installation of screws and scraper conveyors their unilateral servicing with width of easy access of at least 0,8 of meters is allowed.

rough

1272-1.

Covers of casings, screws and scraper conveyors (except special observation ports and hatches) are equipped with the blocking excluding access to the rotating and moving parts of screws and scraper conveyors during their work

rough

1284.

Availability on all conveyors of the devices providing emergency stop of the drive from any point on conveyor length from the main passes

rough

1336.

When blocking work of ventilating and aspiration installations with the capital and service equipment additional starting arrangements directly at the ventilating or aspiration equipment are provided.

rough

1336-1.

Non-admission turning on of processing equipment before start-up of the ventilating system blocked with it

rough

1367.

Tunnels in which pulpovoda are laid are equipped with ventilation, emergency lighting and passes by m 0,8 width for service personnel are established. Aeration and air vents of tunnels need to be supported constantly in working order.

considerable

1389.

Non-admission of dumping into the tailings dam of the sewage which is not provided by the project, warehousings of materials, accumulatings of excessive amount of water in comparison with data in the project documentation.

rough

1389-1.

Non-admission of dumping of water from the store in natural reservoirs without cleaning and neutralization

rough

1495.

Survey and repair of collectors is carried out by link numbering at least three people. The people who are in collector or well more than 5 m in depth are supplied with gas analyzer, lamps, bilateral wire communication or radio communication with the people who are at entrance to collector or well

considerable

1544.

Natural observations of condition of the protecting dams and dikes include instrumental control, with use of the instrumentations established on them.

considerable

1655.

The works connected with construction, operation, expansion, reconstruction, upgrade, preservation and liquidation of hazardous production facilities of coal mines are performed according to the project documentation and the plan of mining operations.

rough

1658.

The coal mines conducting underground mining operations are equipped with watch systems behind personnel, notifications about accidents, positioning and search of personnel, the direct telephone and duplicating it alternative link with the servicing PASS OPB.

rough

1660.

Providing all PASS OPB which are going down to the mine the isolating self-rescuer, except for when conducting emergency works. Its fixing to each underground worker of the mine. Availability of the isolating self-rescuers is 10 percent more than payroll of the workers occupied at underground works. The organization of Items of switching (no more than one along the line) or installation of group portable or stationary means of self-rescuing which arrangement is approved with PASS OPB, in mines with the remote work locations, from which exit in case of accidents to the safe place which is not providing with time of protective action of the self-rescuer

rough

1664.

Appointment to positions of technical leads – chief engineers of the mines dangerous on sudden emissions of coal and gas, workers (specialists) having higher education and length of service on executive positions in the organization corresponding to profile at least 5 years and also work experience on the leading and engineering positions at underground works at least 5 years, including at least 3 years in the mines dangerous on sudden emissions of coal and gas.

considerable

1667.

Availability in the working days of the mine and change in developments, deadlock and remote from workplaces (which list is determined by the technical lead of the mine during accident elimination scheduling), and in days and changes, non-working for mines, in any developments, at least two experienced workers having length of service in more than 6 months, in the presence at them gas-determinant with sound signal of continuous action.

considerable

1677.

Acceptance of distance between крепью and ladder, at its basis, is at least 0, meter. Width of ladders – is at least 0,4 of meters, and distance between steps – no more 0,4 of meters

rough

1681.

Compliance of the carried-out excavations to projects and passports of carrying out developments of all useful life

rough

1681-1.

Non-admission of conducting mining operations without the approved passport of carrying out and fixture of excavations

rough

1682.

Availability of the minimum areas of cross sections, square meters in light: the main otkatochny and ventilating developments, human trips for the mechanized transportation - 12,8

considerable

1682-1.

Availability of the minimum areas of cross sections, square meters in light: local ventilating, intermediate, conveyor and heat-sink shtrek, local bremsberg and biases – 10,3

considerable

1682-2.

Availability of the minimum areas of cross sections, square meters in light: ventilating glades, furnaces, kosovichnik – 6,0

considerable

1682-3.

Availability of the minimum areas of cross sections, square meters in light: the local developments which are in zone of influence of clearing works, are not intended for the mechanized transportation of people – 10,3

considerable

1689.

In case of parallel conducting works on driving of trunk and to construction of constant fix from suspended regiment availability of upper floor for protection of the objects working at the shelf from possible fall from above. Acceptance of gap between regiment and built крепью trunk, timbering or board cover, considering from speakers of edges of curve pieces, no more than 120 millimeters and in operating time its dense overlapping the special devices provided in design of regiment or board cover.

considerable

1703.

Availability of passports on installation and dismantle of the clearing complexes approved by the technical lead of the mine

considerable

1711.

Works on artificial collapse of roof are performed according to the additional developed actions approved by the technical lead of the mine.

rough

1719.

Laying of field developments according to the Instruction developed and approved by the organization in coordination with authorized body in the field of industrial safety

considerable