Order of the Government of the Russian Federation "About Approval of the Single List of Products, the Subject Obligatory Certification, and the Single List of Products Which Are Subject to Declaring of Compliance, Introduction of Amendments to the Resolution..."

ORDER OF THE GOVERNMENT OF THE RUSSIAN FEDERATION

of December 23, 2021 No. 2425

About approval of the single list of products, the subject obligatory certification, and the single list of products which are subject to declaring of compliance, modification of the Order of the Government of the Russian Federation of December 31, 2020 No. 2467 and recognition voided some acts of the Government of the Russian Federation

(In edition of Orders of the Government of the Russian Federation of 12.06.2024 No. 792, 17.08.2024 No. 1113, 14.05.2025 No. 642, 11.09.2025 No. 1403, 28.01.2026 No. 63, 27.11.2025 No. 1891)

According to Item 3 of article 46 of the Federal law "About Technical Regulation" Government of the Russian Federation decides:

1. Approve enclosed:

the single list of products which are subject to obligatory certification;

the single list of products which are subject to declaring of compliance.

2. Ceased to be valid

3. Determine that:

certificates of conformity and declarations of conformity concerning products included in the single list of products which are subject to obligatory certification and the single list of products which confirmation of conformity is performed in the form of adoption of the declaration of conformity approved by the order of the Government of the Russian Federation of December 1, 2009 No. 982 "About approval of the single list of products, the subject obligatory certification, and the single list of products which confirmation of conformity is performed in the form of adoption of the declaration of conformity" issued (accepted) to day entries into force of this resolution are considered valid before the termination of the term established in them during expiration date or the service life of products established in accordance with the legislation of the Russian Federation, but no later than September 1, 2025;

from the date of entry into force of this resolution issue of certificates of conformity or adoption of declarations of conformity of products specified in the paragraph the second this Item is not allowed;

till September 1, 2025 production and release into the stream of commerce in the territory of the Russian Federation of the products specified in the paragraph the second this Item, conforming to mandatory requirements of national standards which compliance is confirmed with the valid certificates of conformity or declarations of conformity issued (accepted) by results of obligatory confirmation of conformity of such products are allowed;

till September 1, 2023 production and release into the stream of commerce in the territory of the Russian Federation of products without documents on obligatory confirmation of conformity of products and not marked by market access mark concerning products which were not subject to obligatory confirmation of conformity about day of entry into force of this resolution are allowed;

the certificates of conformity and declarations of conformity issued (accepted) on products which are specified in the single list of products the subject obligatory certification, and the single list of products which are subject to declaring of compliance approved by this resolution and concerning which documents on the standardization establishing requirements and methods of researches (testing) and measurements were changed according to the order of the Government of the Russian Federation of May 14, 2025 to No. 642 "About modification of the order of the Government of the Russian Federation of December 23, 2021 No. 2425" are considered valid before the termination of term of their action, but no later than September 1, 2026;

till September 1, 2026 production and release into the stream of commerce in the territory of the Russian Federation of products specified in paragraph six of this Item according to earlier established requirements, and also certificates of conformity and declarations of conformity on these products issued (accepted) about day of entry into force of the order of the Government of the Russian Federation of May 14, 2025 to No. 642 "About modification of the order of the Government of the Russian Federation of December 23, 2021 No. 2425" are allowed.

4. To Federal Agency for Technical Regulation and Metrology to organize:

in 2-month time from the date of official publication of this resolution placement on the official site of Federal Agency for Technical Regulation and Metrology on the Internet, including in the form of open data, the single list of products, the subject obligatory certification, and the single list of products which are subject to declaring of compliance approved by this resolution (further - single lists of products), and also the list of national standards, references to which are contained in single lists of products;

audit and in necessary cases review and (or) updating of national standards from the date of inclusion of such standards in single lists of products at least once in 5 years;

informing the Government of the Russian Federation at least in one year about the planned changes of the national standard or about the planned cancellation of the national standard which is included in single lists of products.

5. To the Ministry of Industry and Trade of the Russian Federation to organize modification of single lists of products according to methodical recommendations, stipulated in Item 6 these resolutions, including changes in case of cancellation by Federal Agency for Technical Regulation and Metrology of the national standards establishing mandatory requirements to products included in single lists of products, and (or) the rule and methods of researches (testing) and measurements of such products when holding procedures of obligatory confirmation of conformity.

6. To the Ministry of Industry and Trade of the Russian Federation to approve till September 1, 2023 methodical recommendations about development of offers on refining of the single list of products, the subject obligatory certification, and the single list of products which are subject to declaring of compliance.

7. Recognize invalid acts of the Government of the Russian Federation according to the list according to appendix.

8. This resolution becomes effective since September 1, 2022 and is effective till September 1, 2028, except for:

Items 2, 4, 5 and 6 these resolutions which become effective from the date of its official publication;

Items 5.2 - 5.4, 5.6 - 5.8, of Sections 6 and 7, Items 15. 2, 15.21, 15.26, 15.32 - 15.36, 16.2 - 16.7, 16.12, 17.3, 17.5, 17.14, 21.1, 21.2 and Sections 22 - the 26th single list of products which are subject to obligatory certification and subitems 1.1.1 - 1.1.3, Items 1. 2, 1. 4, 7. 1, 10.6 and 10.7 and Sections 65 and 66 of the single list of products which are subject to declaring of compliance which become effective since September 1, 2023.

Russian Prime Minister

M. Mishustin

Approved by the Order of the Government of the Russian Federation of December 23, 2021, No. 2425

The single list of products which are subject to obligatory certification

Product name

Identification of products by code of the CN FEA EEU <1>

Documents on the standardization establishing requirements to products

Documents on the standardization establishing methods of researches (testing) and measurements

Electric power <2>

1.1.

Electrical energy in power networks of general purpose of alternating three-phase and single-phase current with a frequency of 50 Hz

interstate standard

GOST 32144-2013 "Electrical energy. Electromagnetic compatibility of technical means. Regulations of quality of electrical energy in utility power systems of general purpose", No. 400 of St enacted as the national standard of the Russian Federation since July 1, 2014 by the order of Federal Agency for Technical Regulation and Metrology of July 22, 2013 "About enforcement of the interstate standard", regarding the requirements established in subitems 4.2.1 and 4.2.2 of Item 4.2 of Section 4 of the specified standard

interstate standard

GOST IEC 61000-4-30-2017 "Electromagnetic compatibility (EMS). Part 4-30. Test methods and measurements. Methods of measurements of quality of electrical energy", No. 1981 of St enacted as the national standard of the Russian Federation since December 1, 2018 by the order of Federal Agency for Technical Regulation and Metrology of December 14, 2017 "About enforcement of the interstate standard"

Oil products light.

Alternative types of fuel

2.1.

Etanolny motor fuel for automobile engines with forced ignition. Benzanola

from 2710

the national state standard specification P 52201-2004 standard "Fuel motor etanolny for automobile engines with forced ignition. Benzanola. General technical requirements", No. 13 of St approved and enacted since July 1, 2004 by the resolution of the State committee of the Russian Federation on standardization and metrology of January 15, 2004 "About approval and enforcement of the national standard of the Russian Federation", regarding the requirements established in Item 4.1 of Section 4 of the specified standard

interstate standard

GOST 8226-2022 "Fuel for engines. Research method of determination of octane rating", No. 1588 of St enacted as the national standard of the Russian Federation since July 1, 2023 by the order of Federal Agency for Technical Regulation and Metrology of December 26, 2022 "About enforcement of the interstate standard"

interstate standard

GOST 28828-90 "Gasolines. Lead determination method", No. 3449 approved and enacted since January 1, 1992 by the resolution of the State committee of the USSR on product quality control and standards of December 28, 1990 "About approval and enforcement of state standard "Gasolines. Lead determination method"

national standard

GOST P 51942-2019 "Gasolines. Lead determination by method of atomic and absorbing spectrometry", No. 1234 of St approved and enacted since July 1, 2020 by the order of Federal Agency for Technical Regulation and Metrology of November 22, 2019 "About approval of the national standard"

interstate standard

GOST E№13132-2012 "Oil products liquid. Gasoline unleaded. Determination of organic oxygencontaining compounds and general content of integrally connected oxygen by method of gas chromatography with use of the switching columns", No. 172 of St enacted as the national standard of the Russian Federation since July 1, 2014 by the order of Federal Agency for Technical Regulation and Metrology of June 19, 2013 "About enforcement of the interstate standard"

interstate standard

GOST E№1601-2017 "Oil products liquid. Gasoline unleaded. Determination of organic oxygen-containing compounds and general content of integrally connected oxygen by method of gas chromatography with use of the flame and ionization detector on oxygen (O-FID)", No. 901 of St enacted as the national standard of the Russian Federation since January 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of October 31, 2018 "About enforcement of the interstate standard"

interstate standard

GOST E№13016-1-2013 "Oil products liquid. Part 1. Determination of pressure of the saturated steam containing air (ASVP), and calculation of equivalent pressure of dry steam (DVPE)", No. 722 of St enacted since January 1, 2015 by the order of Federal Agency for Technical Regulation and Metrology of November 22, 2013 "About enforcement of the interstate standard"

interstate standard

GOST ISO 3405-2022 "Oil products. Determination of fractional structure with atmospheric pressure", No. 1104 of St enacted as the national standard of the Russian Federation since July 1, 2023 by the order of Federal Agency for Technical Regulation and Metrology of October 10, 2022 "About enforcement of the interstate standard"

interstate standard

GOST ISO 8754-2013 "Oil products. Determination of sulfur content by method of power dispersive X-ray fluorescent spectrometry", No. 895 of St enacted as the national standard of the Russian Federation since January 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of October 31, 2018 "About enforcement of the interstate standard"

interstate standard

GOST E№12177-2013 "Oil products liquid. Gasoline. Benzene content determination by gazokhromatografichesky method", No. 720 of St enacted as the national standard of the Russian Federation since January 1, 2015 by the order of Federal Agency for Technical Regulation and Metrology of November 22, 2013 "About enforcement of the interstate standard"

national standard

GOST 2177-99 (ISO 3405-88) "Oil products. Methods of determination of fractional structure", No. 300 of St enacted as state standard of the Russian Federation since January 1, 2001 by the resolution of the State committee of the Russian Federation on standardization and metrology of September 21, 1999 "About enforcement of the interstate standard"

interstate standard

GOST 19121-73 "Oil products. Method of determination of sulfur content burning in lamp", No. 2121 approved and enacted since July 1, 1974 by the resolution of the State committee of the USSR on standards of August 10, 1973 "About approval of state standard of GOST 19121-73 "Oil products. Method of determination of sulfur content burning in lamp"

interstate standard

GOST 33194-2014 "Oil and oil products. Determination of sulfur content by method of X-ray fluorescent spectrometry with wave dispersion", No. 891 of St enacted as the national standard of the Russian Federation since January 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of October 31, 2018 "About enforcement of the interstate standard"

interstate standard

GOST 32338-2022 "Gasolines. Determination of MTBE, ETBE, TAME, DIPE, methanol, ethanol and tert-butanol by method of infrared spectroscopy", No. 1102 of St enacted as the national standard of the Russian Federation since July 1, 2023 by the order of Federal Agency for Technical Regulation and Metrology of October 10, 2022 "About enforcement of the interstate standard"

interstate standard

GOST 32139-2024 "Oil and oil products. Determination of sulfur content by method of power dispersive X-ray fluorescent spectrometry", No. 901 of St enacted as the national standard of the Russian Federation since July 1, 2025 by the order of Federal Agency for Technical Regulation and Metrology of July 4, 2024 "About enforcement of the interstate standard"

national standard

GOST P 51859-2002 "Oil products. Sulfur determination by lamp method", No. 3 of St accepted and enacted since January 1, 2003 by the resolution of the State committee of the Russian Federation on standardization and metrology of January 8, 2002 "About acceptance of state standard"

national standard

GOST P 51947-2002 "Oil and oil products. Sulfur determination by method of power dispersive X-ray fluorescent spectrometry", No. 368 of St accepted and enacted since July 1, 2003 by the resolution of the State committee of the Russian Federation on standardization and metrology of October 9, 2002 "About acceptance of state standard"

interstate standard

GOST ISO 14596-2016 "Oil products. Determination of sulfur content by method of X-ray fluorescent spectrometry with dispersion on wavelength", No. 246 of St enacted as the national standard of the Russian Federation since July 1, 2018 by the order of Federal Agency for Technical Regulation and Metrology of April 4, 2017 "About enforcement of the interstate standard"

interstate standard

GOST 34603-2019 "Fuels for engines with spark ignition. Benzene determination by method of spectroscopy of the average infrared range", No. 1238 of St enacted as the national standard of the Russian Federation since July 1, 2020 by the order of Federal Agency for Technical Regulation and Metrology of November 22, 2019 "About enforcement of the interstate standard"

interstate standard

GOST 29040-2018 "Gasolines. Method of determination of benzene and total content of aromatic hydrocarbons", No. 563 of St enacted as the national standard of the Russian Federation since July 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of September 4, 2018 "About enforcement of the interstate standard"

national standard

GOST P 51930-2002 "Gasolines automobile and aviation. Benzene determination by method of infrared spectroscopy", No. 309 of St accepted and enacted since July 1, 2003 by the resolution of the State committee of the Russian Federation on standardization and metrology of August 23, 2002 "About acceptance of state standard"

interstate standard

GOST 5066-2018 "Fuels motor. Methods of determination of temperatures of opacification, the beginning of crystallization and freezing", No. 660 of St enacted as the national standard of the Russian Federation since July 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of September 27, 2018 "About enforcement of the interstate standard"

Solid hydrocarbons (oil and slate)

3.1.

Paraffin oil firm (except the T-3, T-1, T-2, brands C)

from 2712

interstate standard

GOST 23683-2021 "Paraffin oil firm. Specifications", No. 696 of St enacted as the national standard of the Russian Federation since January 1, 2022 by the order of Federal Agency for Technical Regulation and Metrology of August 6, 2021 "About enforcement of the interstate standard", regarding the requirements established:

in Item 4.2 of Section 4 of the specified standard;

in Section 5 of the specified standard

interstate standard

GOST 4255-75 "Oil products. Method of determination of temperature of melting according to Zhukov", No. 2087 approved and enacted since July 1, 1976 by the resolution of the State committee of the USSR on standards of August 7, 1975 "About acceptance of state standard of GOST 4255-75 "Oil products. Method of determination of temperature of melting according to Zhukov"

interstate standard

GOST 9090-2000 (ISO 2908-74) "Paraffin oil. Oil content determination method", No. 246 of St enacted as state standard of the Russian Federation since July 1, 2001 by the resolution of the State committee of the Russian Federation on standardization and metrology of October 3, 2000 "About enforcement of the interstate standard"

state standard

GOST 25337-82 "Paraffin oil. Method of determination of color on the colorimeter KNS-2", No. 2702 approved and enacted since July 1, 1983 by the resolution of the State committee of the USSR on standards of July 16, 1982 "About approval of state standard of GOST 25337-82 "Paraffin oil. Method of determination of color on the colorimeter KNS-2"

interstate standard

GOST 25771-83 "Paraffin and ceresins oil. Method of determination of penetration needle", No. 2115 approved and enacted since July 1, 1983 by the resolution of the State committee of the USSR on standards of April 27, 1983 "About approval of state standard of GOST 25771-83 "Paraffin and ceresins oil. Method of determination of penetration needle"

state standard

GOST 1437-75 "Oil products dark. The accelerated sulfur determination method", No. 1342 approved and enacted since January 1, 1977 by the resolution of the State committee of the USSR on standards of May 19, 1975 "About approval of state standard of GOST 1437-75 "Oil products dark. The accelerated sulfur determination method"

interstate standard

GOST 2477-2014 "Oil and oil products. Water content determination method", No. 399 of St enacted as the national standard of the Russian Federation since July 1, 2016 by the order of Federal Agency for Technical Regulation and Metrology of May 21, 2015 "About enforcement of the interstate standard"

interstate standard

GOST 6370-2018 "Oil, oil products and additives. Method of determination of mechanical impurity", No. 666 of St enacted as the national standard of the Russian Federation since December 1, 2023 by the order of Federal Agency for Technical Regulation and Metrology of September 27, 2018 "About enforcement of the interstate standard"

interstate standard

GOST 6307-75 "Oil products. Method of determination of availability of water-soluble acids and alkalis", the USSR approved and enacted since January 1, 1977 by the resolution of the State committee of standards of Council of Ministers of July 30, 1975 No. 2001 "About approval of state standard of GOST 6307-75 "Oil products. Method of determination of availability of water-soluble acids and alkalis"

interstate standard

Excluded

Pipes and details of pipelines from thermolayers

5.1.

Pipes polyethylene pressure head for economic and drinking water supply

from 3917 21 100 0

national standard

GOST P 70628.2-2023 (ISO 4427-2:2019) "Pipelines from plastic for water supply, drainage and the pressure head sewerage. Polyethylene (PE). Part 2. Pipes", No. 51 of St approved and enacted since September 1, 2024 by the order of Federal Agency for Technical Regulation and Metrology of January 26, 2023 "About approval of the national standard of the Russian Federation", regarding the requirements established:

in Item 5.1 of Section 5 of the specified standard;

in Items 7.2 and 7.3 of Section 7 of the specified standard;

in Item 8.2 (the table 3, line items 1 - 3) Section 8 of the specified standard;

in Section 9 (the table 5, line items 1 - 4, 6 and 7, only for pipes PE 100-RC (notes 8 and 9) the specified standard;

in Section 12 of the specified standard;

in the Item A.6 of appendix A of the specified standard

national standard

interstate standard

GOST ISO 3126-2023 "Pipelines from plastic. Plastic elements of the pipeline. Determination of the sizes", No. 1436 of St enacted as the national standard of the Russian Federation since December 1, 2024 by the order of Federal Agency for Technical Regulation and Metrology of November 21, 2023 "About enforcement of the interstate standard"

interstate standard

GOST ISO 6259-1-2023 "Pipes from thermolayers. Determination of mechanical properties in case of stretching. Part 1. Common method of testing", No. 1713 of St enacted as the national standard of the Russian Federation since December 1, 2024 by the order of Federal Agency for Technical Regulation and Metrology of December 28, 2023 "About enforcement of the interstate standard"

national standard

GOST P 70628.1-2023 (ISO 4427-1:2019) "Pipelines from plastic for water supply, drainage and the pressure head sewerage. Polyethylene (PE). Part 1. General requirements", No. 50 of St approved and enacted since September 1, 2024 by the order of Federal Agency for Technical Regulation and Metrology of January 26, 2023 "About approval of the national standard of the Russian Federation", regarding the requirements established in Item 5.3 (the table 1, line item 2) Section 5 of the specified standard

interstate standard

GOST ISO 6259-3-2023 "Pipes from thermolayers. Determination of mechanical properties in case of stretching. Part 3. Pipes from polyolefins", No. 1715 of St enacted as the national standard of the Russian Federation since December 1, 2024 by the order of Federal Agency for Technical Regulation and Metrology of December 28, 2023 "About enforcement of the interstate standard"

interstate standard

GOST 27078-2014 (ISO 2505:2005) "Pipes from thermolayers. Change of length. Method of determination and parameters", No. 743 of St enacted as the national standard of the Russian Federation since March 1, 2016 by the order of Federal Agency for Technical Regulation and Metrology of June 18, 2015 "About enforcement of the interstate standard"

interstate standard

GOST ISO 1167-1-2013 "Pipes, connecting details and nodes of connections from thermolayers for transportation of liquid and gaseous circles. Determination of resistance to internal pressure. Part 1. Common method", No. 201 of St enacted as the national standard of the Russian Federation since August 1, 2014 by the order of Federal Agency for Technical Regulation and Metrology of March 20, 2014 "About enforcement of the interstate standard"

interstate standard

GOST ISO 1167-2-2013 "Pipes, connecting details and nodes of connections from thermolayers for transportation of liquid and gaseous circles. Determination of resistance to internal pressure. Part 2. Preparation of samples of pipes", No. 203 of St enacted as the national standard of the Russian Federation since August 1, 2014 by the order of Federal Agency for Technical Regulation and Metrology of March 20, 2014 "About enforcement of the interstate standard"

interstate standard

GOST IEC 60811-605-2016 "Cables electric and fiber-optical. Test methods of nonmetallic materials. Part 605. Physical testing. Determination of content of soot and (or) mineral filler in polyethylene compositions", No. 836 of St enacted as the national standard of the Russian Federation since November 1, 2017 by the order of Federal Agency for Technical Regulation and Metrology of August 8, 2017 "About enforcement of the interstate standard"

state standard

GOST 26311-84 (ST of SEV 4061-83) "Polyolefins. Soot determination method", No. 3703 approved and enacted since July 1, 1985 by the resolution of the State committee of the USSR on standards of October 26, 1984 "About approval of state standard "Polyolefins. Soot determination method"

interstate standard

GOST IEC 60811-511-2015 "Cables electric and fiber-optical. Test methods of nonmetallic materials. Part 511. Mechanical testing. Measure definition of flowability of fusion of polyethylene compositions", No. 1292 of St enacted as the national standard of the Russian Federation since July 1, 2017 by the order of Federal Agency for Technical Regulation and Metrology of September 30, 2016 "About enforcement of the interstate standard"

interstate standard

GOST IEC 60811-406-2015 "Cables electric and fiber-optical. Test methods of nonmetallic materials. Part 406. Different testing. Resistance of polyethylene and polypropylene compositions to cracking under the influence of tension", No. 1275 of St enacted as the national standard of the Russian Federation since July 1, 2017 by the order of Federal Agency for Technical Regulation and Metrology of September 30, 2016 "About enforcement of the interstate standard"

interstate standard

GOST 11262-2017 (ISO 527-2:2012) "Plastic. Test method on stretching", No. 45 of St enacted as the national standard of the Russian Federation since October 1, 2018 by the order of Federal Agency for Technical Regulation and Metrology of February 2, 2018 "About enforcement of the interstate standard"

national standard

GOST P 56756-2015 (ISO 11357-6:2008) "Plastic. Differential Scanning Calorimetry (DSC). Part 6. Determination of time of oxidizing induction (isothermal VOI) and temperatures of oxidizing induction (dynamic TOI)", No. 1958 of St approved and enacted since January 1, 2017 by the order of Federal Agency for Technical Regulation and Metrology of November 24, 2015 "About approval of the national standard"

national standard

GOST P 58121.2-2018 (ISO 4437-2:2014) "Plastic pipelines for transportation of gaseous fuel. Polyethylene (PE). Part 2. Pipes", No. 297 of St approved and enacted since July 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of May 31, 2018 "About approval of the national standard of the Russian Federation", regarding the requirements established:

in Items 5.1 and 5.2 of Section 5 of the specified standard;

in the Item A.7 of appendix A of the specified standard

interstate standard

GOST 11645-2021 "Plastic. Methods of measure definition of flowability of fusion of thermolayers", No. 1377 of St enacted as the national standard of the Russian Federation since September 1, 2022 by the order of Federal Agency for Technical Regulation and Metrology of October 28, 2021 "About enforcement of the interstate standard"

5.2.

Pipes pressure head of the oriented unplasticized polyvinylchloride (for cold water supply and the pressure head sewerage)

from 3917 23

national standard

GOST P 56927-2016 "Pipes from the oriented unplasticized polyvinylchloride for water supply. Specifications", No. 372 of St approved and enacted since January 1, 2017 by the order of Federal Agency for Technical Regulation and Metrology of May 23, 2016 "About approval of the national standard", regarding the requirements established:

in Item 4.2 of Section 4 of the specified standard;

in subitems 5.1. 1, 5.1.3 - 5.1.5 (the table 6, line item 3) and 5.1.6 Items 5. 1, in Item 5.3 of Section 5 of the specified standard

national standard

in Item 5.3 of Section 5 of the specified standard;

in Items 8.1 and 8.7 of Section 8 of the specified standard

interstate standard

GOST ISO 1167-4-2013 "Pipes, connecting details and nodes of connections from thermolayers for transportation of liquid and gaseous circles. Determination of resistance to internal pressure. Part 4. Preparation of nodes of connections", No. 204 of St enacted as the national standard of the Russian Federation since August 1, 2014 by the order of Federal Agency for Technical Regulation and Metrology of March 20, 2014 "About enforcement of the interstate standard"

interstate standard

GOST ISO 6259-2-2023 "Pipes from thermolayers. Determination of mechanical properties in case of stretching. Part 2. Pipes from unplasticized polyvinylchloride (NPVH), the oriented unplasticized polyvinylchloride (PVH-O), the chlorinated polyvinylchloride (HPVH) and shock-resistant polyvinylchloride (UPVH)", No. 1714 of St enacted as the national standard of the Russian Federation since December 1, 2024 by the order of Federal Agency for Technical Regulation and Metrology of December 28, 2023 "About enforcement of the interstate standard"

5.3.

Pipes pressure head of unplasticized polyvinylchloride (for cold water supply)

from 3917 23

national standard

GOST P 51613-2000 "Pipes pressure head of unplasticized polyvinylchloride. Specifications", No. 152 of St accepted and enacted since July 1, 2001 by the resolution of the State committee of the Russian Federation on standardization and metrology of June 6, 2000 "About acceptance and enforcement of state standard", regarding the requirements established:

in Item 4.2 of Section 4 of the specified standard;

in Items 5.1 and 5.2 (the table 6, line items 1 - 8, 10 and 11),

in subitem 5.3.1 of Item 5.3 of Section 5 of the specified standard

national standard

in Item 5.3 of Section 5 of the specified standard;

in Items 8.2 and 8.5 of Section 8 of the specified standard

interstate standard

GOST 4647-2015 "Plastic. Method of determination of impact strength across Sharpi", No. 1915 of St enacted as the national standard of the Russian Federation since January 1, 2017 by the order of Federal Agency for Technical Regulation and Metrology of November 20, 2015 "About enforcement of the interstate standard"

interstate standard

5.4.

Pipes pressure head polymeric single-layer of polyvinylchloride

from 3917 23

interstate standard

GOST 32415-2013 "Pipes pressure head of thermolayers and connecting details to them for water supply systems and heating. General specifications", No. 2387 of St enacted as the national standard of the Russian Federation since January 1, 2015 by the order of Federal Agency for Technical Regulation and Metrology of December 30, 2013 "About enforcement of the interstate standard", regarding the requirements established:

in subitems 4.1.1 - 4.1.4 Items 4.1 of Section 4 of the specified standard;

in subitems 5.1.2 (the table 8), 5.1.4 - 5.1.6 and 5.1.8 Items 5. 1, in subitems 5.4.1 and 5.4.2.2 of Item 5. 4, in subitem 5.6.1 of Item 5.6 of Section 5 of the specified standard

interstate standard

in Item 5.6 of Section 5 of the specified standard;

in Items 8. 2, 8.4, 8.5 and 8.11 - 8.15 of Section 8 of the specified standard

interstate standard

5.5.

Pipes polyethylene for transportation of gaseous fuel

from 3917 21 100 0

national standard

in Items 4.1 and 4.2 of Section 4 of the specified standard;

in Items 5.1 and 5.2 of Section 5 of the specified standard;

in Items 6.2 and 6.3 of Section 6 of the specified standard;

in Item 7.2 (the table 4) Section 7 of the specified standard;

in Item 8.2 (the table 6, line items 1 and 3) Section 8 of the specified standard;

in Item 10.2 (the table 7) Section 10 of the specified standard;

in the Item A.7 of appendix A of the specified standard

national standard

GOST P 58121.1-2018(ISO 4437-1:2014) "Plastic pipelines for transportation of gaseous fuel. Polyethylene (PE). Part 1. General provisions", No. 296 of St approved and enacted since July 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of May 31, 2018 "About approval of the national standard of the Russian Federation", regarding the requirements established by appendices DV, DG and DD of the specified standard

national standard

in Items 5.1 and 5.2 of Section 5 of the specified standard;

in Item 10.2 of Section 10 of the specified standard

national standard

GOST P 58121.1-2018 (ISO 4437-1:2014) "Plastic pipelines for transportation of gaseous fuel. Polyethylene (PE). Part 1. General provisions", No. 296 of St approved and enacted since July 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of May 31, 2018 "About approval of the national standard of the Russian Federation", regarding the requirements established in subitems 6.2.3.1 (the table 1, line item 7) and 6.2.3.2 (the table 2) Item 6.2 (regarding indicator "resistance to gas condensate"), in Item 6.3 (the table 3) Section 6 of the specified standard

interstate standard

national standard

interstate standard

national standard

GOST P 54475-2011 "Pipes polymeric with the structured wall and shaped parts to them for systems of the outside sewerage. Specifications", No. 474 of St approved and enacted since May 1, 2012 by the order of Federal Agency for Technical Regulation and Metrology of October 20, 2011 "About approval of the national standard", regarding the requirements established in Items 8.4 and 8.5 of Section 8 of the specified standard

interstate standard

state standard of GOST 15139-69 (ST of SEV 891-78) "Plastic. Methods of determination of density (volume weight)", No. 1365 approved and enacted since July 1, 1970 by the resolution of Committee of standards, measures and measuring devices under Council of Ministers of the USSR of December 17, 1969 "About approval of state standard of GOST 15139-69 "Plastic. Methods of determination of density (volume weight)"

interstate standard

GOST 16338-85 "Polyethylene of low pressure. Specifications", No. 4272 approved and enacted since January 1, 1987 by the resolution of the State committee of the USSR on standards of December 20, 1985 "About approval of state standard "Polyethylene of low pressure. Specifications"

state standard

GOST 26359-84 (ST of SEV 4064-83) "Polyethylene. Method of determination of volatiles", No. 4503 approved and enacted since July 1, 1985 by the resolution of the State committee of the USSR on standards of December 18, 1984 "About approval of state standard "Polyethylene. Method of determination of volatiles"

interstate standard

GOST 14870-77 "Chemical goods. Water determination methods", the USSR approved and enacted since January 1, 1978 by the resolution of the State committee of standards of Council of Ministers of January 13, 1977 No. 97 "About approval of state standard "Chemical goods. Water determination methods"

interstate standard

GOST ISO 18553-2023 "Pipes, fitting and compositions from polyolefins. Evaluation method of extent of distribution of pigment or technical carbon", No. 182 of St enacted as the national standard of the Russian Federation since December 1, 2024 by the order of Federal Agency for Technical Regulation and Metrology of February 2, 2024 "About enforcement of the interstate standard"

5.6.

Pipes metalbedded (for heat supply without heat insulation)

from 3917 39

national standard

GOST P 53630-2015 "Pipes pressure head multilayer for water supply systems and heating. General specifications", No. 1890 of St approved and enacted since June 1, 2016 by the order of Federal Agency for Technical Regulation and Metrology of November 19, 2015 "About approval of the national standard", regarding the requirements established:

in subitem 4.1.2 of Item 4.1 of Section 4 of the specified standard;

in subitems 5.1.1 - 5.1.4 and 5.1.8 Items 5. 1, in subitem 5.2.1 of Item 5. 2, in subitems 5.4.1 and 5.4.2 of Item 5.4 of Section 5 of the specified standard

national standard

interstate standard

in Item 5.6 of Section 5 of the specified standard;

in Items 8.2 and 8.18 of Section 8 of the specified standard

5.7.

Pipes pressure head polymeric tough other for heat supply without heat insulation

5.7.1.

Pipes pressure head polymeric multilayer of the sewed polyethylene

from 3917 21

national standard

in subitem 4.1.2 of Item 4.1 of Section 4 of the specified standard;

in subitems 5.1. 1, 5.1. 2, 5.1.6 and 5.1.8 Items 5. 1, in subitem 5.4.1 of Item 5.4 of Section 5 of the specified standard

national standard

interstate standard

5.7.2.

Pipes pressure head polymeric multilayer (except pipes from the sewed polyethylene)

from 3917 21

3917 22

3917 23

3917 29

3917 31

3917 32

3917 33

national standard

in subitem 4.1.2 of Item 4.1 of Section 4 of the specified standard;

in subitems 5.1. 1, 5.1.2 and 5.1.6 Items 5. 1, in subitem 5.4.1 of Item 5.4 of Section 5 of the specified standard

national standard

interstate standard

5.7.3.

Pipes pressure head polymeric single-layer of the sewed polyethylene

from 3917 21

interstate standard

in subitems 4.1.1 - 4.1.4 Items 4.1 of Section 4 of the specified standard;

in subitems 5.1. 1, 5.1.2 (table 9), 5.1.4, 5.1.5 and 5.1.11 of Item 5. 1, in subitem 5.4.2.4 of Item 5. 4, in subitem 5.6.1 of Item 5.6 of Section 5 of the specified standard

interstate standard

in Item 5.6 of Section 5 of the specified standard;

in Items 8. 2, 8.5, 8.6 and 8.18 of Section 8 of the specified standard

interstate standard

5.7.4.

Pipes pressure head polymeric single-layer of polyethylene of the raised PE-RT thermal stability

from 3917

interstate standard

in subitems 4.1.1 - 4.1.4 Items 4.1 of Section 4 of the specified standard;

in subitems 5.1. 1, 5.1.2 (table 13), 5.1.4 and 5.1.5 Items 5. 1, in subitems 5.4.1 and 5.4.2.7 of Item 5. 4, in subitem 5.6.1 of Item 5.6 of Section 5 of the specified standard

interstate standard

in Item 5.6 of Section 6 of the specified standard;

in Items 8.2 and 8.4 - 8.6 Sections 8 of the specified standard

interstate standard

5.7.5.

Pipes pressure head polymeric single-layer of polypropylene

from 3917 22

interstate standard

in subitems 4.1.1 - 4.1.4 Items 4.1 of Section 4 of the specified standard;

in subitems 5.1. 1, 5.1.2 (table 10), 5.1.4, 5.1.5 and 5.1.7 of Item 5. 1, in subitems 5.4.1 and 5.4.2.3 of Item 5. 4, in subitem 5.6.1 of Item 5.6 of Section 5 of the specified standard

interstate standard

in Item 5.6 of Section 5 of the specified standard;

in Items 8. 2, 8.4 - 8.6 and 8.14 Sections 8 of the specified standard

interstate standard

5.7.6.

Pipes pressure head polymeric single-layer of polybutene

from 3917 22

interstate standard

in subitems 4.1.1 - 4.1.4 Items 4.1 of Section 4 of the specified standard;

in subitems 5.1. 1, 5.1.2 (table 11), 5.1.4 and 5.1.5 Items 5. 1, in subitems 5.4.1 and 5.4.2.5 of Item 5. 4, in subitem 5.6.1 of Item 5.6 of Section 5 of the specified standard

interstate standard

in Item 5.6 of Section 5 of the specified standard;

in Items 8.2 and 8.4 - 8.8 Sections 8 of the specified standard

interstate standard

5.8.

Fitting is other plastic

5.8.1.

Fitting from polyethylene for transportation of gaseous fuel

3917 40 000 9

national standard

GOST P 58121.3-2018 (ISO 4437-3:2014) "Plastic pipelines for transportation of gaseous fuel. Polyethylene (PE). Part 3. Fitting", No. 298 of St approved and enacted since July 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of May 31, 2018 "About approval of the national standard of the Russian Federation", regarding the requirements established:

in Item 4.1 of Section 4 of the specified standard;

in Items 5. 1, 5.2, 5.4 (for welded fitting) and 5.5 (for electrowelded fitting) Section 5 of the specified standard;

in Items 6.2 (for electrowelded fitting the bell-shaped end), 6.3 (for electrowelded saddle fitting), 6.4 (for fitting with the pipe end) and 6.5 (for fitting for bell-shaped welding) Section 6 of the specified standard;

in Items 7.2 (the table 4, line items 3 (for all types of fitting), 4 (for electrowelded fitting with bell and for bell-shaped welding), 6 (for fitting with the pipe end) and 7.3 (the table 6, for electrowelded fitting with bell and fitting for bell-shaped welding) Section 7 of the specified standard;

in Item 11.2 of Section 11 of the specified standard

national standard

in Items 5. 1, 5.2, 5.4, 5.5 of Section 5 of the specified standard;

in Item 11.2 of Section 11 of the specified standard;

in appendix C, D and DB of the specified standard

national standard

interstate standard

GOST ISO 1167-3-2013 "Pipes, connecting details and nodes of connections from thermolayers for transportation of liquid and gaseous circles. Determination of resistance to internal pressure. Part 3. Preparation of elements of connections", No. 202 of St enacted as the national standard of the Russian Federation since August 1, 2014 by the order of Federal Agency for Technical Regulation and Metrology of March 20, 2014 "About enforcement of the interstate standard"

5.8.2.

Fitting polymeric for pipes pressure head of thermolayers (except fitting from polyvinylchloride and polyethylene)

3917 40 000 9

interstate standard

in subitem 4.2.6 of Item 4.2 of Section 4 of the specified standard;

in subitems 5.2.1 and 5.2.2 of Item 5. 2, in subitems 5.4.1 and 5.4.2 of Item 5. 4, in subitem 5.6.2 of Item 5.6 of Section 5 of the specified standard

interstate standard

in Item 5.6 of Section 5 of the specified standard;

in Item 8.2 of Section 8 of the specified standard

interstate standard

5.8.3.

Fitting from polyvinylchloride for pipes pressure head of thermolayers

3917 40 000 9

interstate standard

in subitem 4.2.6 of Item 4.2 of Section 4 of the specified standard;

in subitems 5.2. 1, 5.2.3 and 5.2.5 Items 5. 2, in subitem 5.4.2.2 of Item 5. 4, in subitem 5.6.2 of Item 5.6 of Section 5 of the specified standard

interstate standard

in Item 5.6 of Section 5 of the specified standard;

in Item 8.2 of Section 8 of the specified standard

interstate standard

national standard

GOST P ISO 580-2008 "Pipelines from plastic. Details connecting molding of thermolayers. Methods of determination of change of appearance after warming up", No. 151 of St approved and enacted since March 1, 2009 by the order of Federal Agency for Technical Regulation and Metrology of July 31, 2008 "About approval of the national standard"

5.8.4.

Fitting from polyethylene for water supply, drainage and the pressure head sewerage

3917 40 000 9

national standard

GOST P 70628.3-2023 (ISO 4427-3:2019) "Pipelines from plastic for water supply, drainage and the pressure head sewerage. Polyethylene (PE). Part 3. Fitting", No. 52 of St approved and enacted since December 1, 2023 by the order of Federal Agency for Technical Regulation and Metrology of January 26, 2023 "About approval of the national standard of the Russian Federation", regarding the requirements established:

in Item 5.1 of Section 5 of the specified standard;

in Items 6. 1, 6.3, 6.5 (for combined fitting of factory production), 6.6 (for pipes of economic and drinking appointment) and 7.2 (for fitting with bell with mortgage heaters) Section 6 of the specified standard;

in Items 7.3 - 7.8 Sections 7 of the specified standard;

in Item 8.3 (the table 4, line items 1, 2 and 4 (only for fitting from PE100-RC), 5 (for fitting with bell with the mortgage heater and fitting with bell), 6 (for saddle fitting with mortgage heaters), 7 (for fitting with the pipe end) and 8 (for saddle fitting with mortgage heaters - for T-shaped branches) Section 8 of the specified standard;

in Item 9.2 (the table 7, line item 1) the specified standard;

in Item 12.2 of Section 12 of the specified standard

national standard

interstate standard

national standard

GOST P 58121.1-2018 (ISO 4437-1:2014) "Plastic pipelines for transportation of gaseous fuel. Polyethylene (PE). Part 1. General provisions", No. 296 of St approved and enacted since July 1, 2019 by the order of Federal Agency for Technical Regulation and Metrology of May 31, 2018 "About approval of the national standard of the Russian Federation", regarding the requirements established in appendices DB and DD of the specified standard

Document in demo-mode!

Full text is available after subscription.

Disclaimer! This text was translated by AI translator and is not a valid juridical document. No warranty. No claim. More info

Effectively work with search system

Database include more 50000 documents. You can find needed documents using search system. For effective work you can mix any on documents parameters: country, documents type, date range, teams or tags.
More about search system

Get help

If you cannot find the required document, or you do not know where to begin, go to Help section.

In this section, we’ve tried to describe in detail the features and capabilities of the system, as well as the most effective techniques for working with the database.

You also may open the section Frequently asked questions. This section provides answers to questions set by users.